Agreement between the European Community and the Swiss Confederation on mutua... (22002A0430(05))
EU - Rechtsakte: 11 External relations

22002A0430(05)

Agreement between the European Community and the Swiss Confederation on mutual recognition in relation to conformity assessment - Final Act - Joint Declarations - Information relating to the entry into force of the seven Agreements with the Swiss Confederation in the sectors free movement of persons, air and land transport, public procurement, scientific and technological cooperation, mutual recognition in relation to conformity assessment, and trade in agricultural products

Official Journal L 114 , 30/04/2002 P. 0369 - 0429
AGREEMENT
between the European Community and the Swiss Confederation on mutual recognition in relation to conformity assessment
THE EUROPEAN COMMUNITY, hereinafter referred to as "the Community", and
THE SWISS CONFEDERATION, hereinafter referred to as "Switzerland",
together hereinafter referred to as "the Parties",
Considering the close ties that exist between the Community and Switzerland;
Considering the Free Trade Agreement of 22 July 1972 between Switzerland and the European Economic Community;
Desiring to conclude an Agreement providing for the mutual recognition of the results of conformity assessment procedures required for access to the respective markets of the Parties;
Considering that mutual recognition in relation to conformity assessment will facilitate trade between the Parties and ensure protection for health, safety, the environment and consumers;
Considering the alignment of legislation will facilitate mutual recognition;
Considering their obligations as Contracting Parties to the Agreement establishing the World Trade Organisation and, in particular, to the Agreement on Technical Barriers to Trade, which encourages the negotiation of mutual recognition agreements;
Considering that mutual recognition agreements contribute to harmonisation at international level of the technical regulations, standards and principles governing implementation of conformity assessment procedures;
Considering that the close ties between the Community and Switzerland, of the one part, and Iceland, Liechtenstein and Norway, of the other, makes the conclusion of parallel agreements between those countries and Switzerland appropriate,
Have agreed to conclude the following Agreement:
Article 1
Purpose
1. The Community and Switzerland hereby grant mutual acceptance of reports, certificates, authorisations and conformity marks issued by the bodies listed in Annex 1 and of the manufacturer's declarations of conformity certifying conformity to the requirements of the other Party in the areas covered by Article 3.
2. In order to avoid duplication of procedures when Swiss and Community requirements are deemed equivalent, the Community and Switzerland shall mutually accept reports, certificates and authorisations issued by the bodies listed in Annex 1 and manufacturer's declarations of conformity certifying conformity to their respective requirements in the areas covered by Article 3. Reports, certificates, authorisations and manufacturer's declarations of conformity shall in particular indicate conformity with the Community legislation. Conformity marks required by the legislation of one of the Parties must be affixed to products placed on the market of that Party.
3. The Committee provided for in Article 10 shall specify the cases in which paragraph 2 shall apply.
Article 2
Definitions
1. For the purposes of this Agreement:
"Conformity assessment" shall mean systematic examination to determine the extent to which a product, process or service fulfils specified requirements;
"Conformity assessment body" shall mean a public or private law body whose activities include performance of all or any stage of the conformity assessment process;
"Designating authority" shall mean an authority with the legal power to designate, suspend, withdraw designation or remove suspension of conformity assessment bodies under its jurisdiction.
2. The definitions laid down by ISO/IEC Guide 2 (1996 edition) and in European standard EN 45020 (1993 edition) in relation to "General terms and their definitions concerning standardisation and related activities" may be used to establish the meaning of the general terms relating to conformity assessment contained in this Agreement.
Article 3
Scope
1. This Agreement covers the obligatory conformity assessment procedures ensuing from the legislative, regulatory and administrative provisions listed in Annex 1.
2. Annex 1 defines the product sectors covered by this Agreement. The Annex is divided up into sectoral chapters and these are subdivided in principle as follows:
section I: legislative, regulatory and administrative provisions;
section II: conformity assessment bodies;
section III: designating authorities;
section IV: special rules relating to the designation of conformity assessment bodies;
section V: any additional provisions.
3. Annex 2 sets out general rules applicable to the designation of conformity assessment bodies.
Article 4
Origin
1. This Agreement shall cover products originating in the Parties, without prejudice to the special provisions laid down in Annex 1.
2. In the event that such products are also covered by agreements on mutual recognition in relation to conformity assessment between Switzerland and Member States of both EFTA and the EEA, the present Agreement shall also cover products of those EFTA Member States.
3. Origin shall be determined in accordance with the rules governing non-preferential origin applicable in each of the Parties or, where appropriate, in the countries referred to in paragraph 2. In the event of divergent rules, the rules of the Party in which the goods will be placed on the market shall apply.
4. Proof of origin may be provided by presentation of a certificate of origin. This certificate shall not be required in the case of imports covered by an EUR 1 movement certificate or by an invoice declaration issued in accordance with Protocol No 3 to the Free Trade Agreement of 22 July 1972 between Switzerland and the EEC, provided that that document indicates as the country of origin one of the Parties or a Member State of both EFTA and the EEA.
Article 5
Conformity assessment bodies
The Parties hereby recognise that the bodies listed in Annex 1 fulfil the conditions of eligibility to assess conformity.
Article 6
Designating authorities
1. The Parties hereby undertake to ensure that their designating authorities have the necessary power and competence to designate or withdraw designation, suspend or remove suspension of the bodies listed in Annex 1. For the designation of conformity assessment bodies, the authorities shall observe the general principles for designation set out in Annex 2, subject to the provisions of the respective section IV in Annex 1. These authorities shall observe the same principles when withdrawing designation, suspending or removing suspension.
2. The decision to include conformity assessment bodies in or remove them from Annex 1 shall be taken on a proposal from one of the Parties in accordance with the procedure set out in Article 11.
3. In the event of the suspension or withdrawal of the suspension by a designating authority of a conformity assessment body listed in Annex 1 under its jurisdiction, the Party concerned shall immediately notify the other Party and the Chairman of the Committee. Reports, certificates, authorisations and conformity marks issued by the conformity assessment body while under suspension need not be recognised by the Parties.
Article 7
Verification of designation procedures
1. The Parties shall exchange information concerning the procedures used to ensure that the conformity assessment bodies under their jurisdiction listed in Annex 1 comply with the general principles of designation outlined in Annex 2 subject to the provisions of the respective section IV in Annex 1.
2. The Parties shall compare methods used to verify conformity of the bodies with the general principles of designation outlined in Annex 2, subject to the provisions of the respective section IV in Annex 1. Existing systems for the accreditation of conformity assessment bodies in the Parties may be used for the purpose of such comparisons.
3. Verification shall be carried out in accordance with the procedure implemented by the Committee under Article 10 below.
Article 8
Verification of compliance of conformity assessment bodies
1. Each Party shall, in exceptional circumstances, have the right to contest the technical competence of the conformity assessment bodies proposed by the other Party or listed in Annex 1 under the jurisdiction of the other Party.
For this purpose, it shall submit in writing an objective and reasoned argument to the other Party and to the Chairman of the Committee.
2. In the event of a disagreement between the Parties, confirmed in the Committee, a verification of the technical competence of the conformity assessment body in question shall be undertaken in accordance with requirements jointly by the Parties, with the participation of the competent authorities concerned.
The result of that verification shall be discussed in the Committee with a view to resolving the issue as soon as possible.
3. Each Party shall ensure that the conformity assessment bodies under its jurisdiction are available for verification of their technical competence as required.
4. Unless otherwise decided by the Committee, the disputed body shall be suspended by the competent designating authority from the time disagreement has been established until agreement has been reached in the Committee.
Article 9
Implementation of the Agreement
1. The Parties shall cooperate with a view to ensuring the satisfactory application of the legislative, regulatory and administrative provisions listed in Annex 1.
2. The designating authorities shall ascertain by appropriate means whether the conformity assessment bodies under their jurisdiction listed in Annex 1 are observing the general principles of designation listed in Annex 2, subject to the provisions listed in the respective section IV in Annex 1.
3. The conformity assessment bodies listed in Annex 1 shall cooperate in an appropriate way in the framework of the coordination and comparison work conducted by each of the Parties in respect of the sectors covered by Annex 1 in order to ensure that the conformity assessment procedures provided for in the laws and regulations of the Parties covered by this Agreement are applied in a consistent manner.
Article 10
Committee
1. A Committee on mutual recognition in relation to conformity assessment (hereinafter referred to as the "Committee"), is hereby established. It shall be composed of representatives of the Parties, and shall be responsible for the management and monitoring of the smooth functioning of this Agreement. To that end, it shall issue recommendations and take decisions in the circumstances provided for in this Agreement. It shall act by mutual agreement.
2. The Committee shall establish its own rules of procedure, which shall contain, inter alia, provisions on the convening of meetings, the appointment of the chairman and the chairman's term of office.
3. The Committee shall meet as and when necessary and at least once a year. Either Party may request the convening of a meeting.
4. The Committee may consider any matter related to this Agreement. In particular, it shall be responsible for:
(a) the inclusion of conformity assessment bodies in Annex 1;
(b) the removal of conformity assessment bodies from Annex 1;
(c) drawing up the procedure for carrying out the verifications provided for in Article 7;
(d) drawing up the procedure for carrying out the verifications provided for in Article 8;
(e) examining any legislative, regulatory and administrative provisions notified by one Party to another pursuant to Article 12 in order to assess their repercussions on the Agreement and to amend the appropriate sections in Annex 1.
5. The Committee may, on a proposal from one of the Parties, modify the Annexes to this Agreement.
Article 11
Inclusion of conformity assessment bodies in annex 1 and their removal
The Committee shall decide to include a conformity assessment body in Annex 1 or to remove it from Annex 1 in accordance with the following procedure:
(a) A Party wishing to add to or remove from Annex 1 any conformity assessment body shall notify the Chairman of the Committee and the other Party of the proposal for a decision to that effect, adding the appropriate information to its request.
(b) If the other Party agrees to the proposal or raises no objection within 60 days of the notification of the proposal, the proposed decision shall be adopted by the Committee.
(c) If the other Party raises objections within that 60-day period, the procedure provided for in Article 8(2) shall be applied.
(d) The Chairman of the Committee shall notify the Parties without delay of all decisions of the Committee. They shall take effect from the date fixed in the decision.
(e) If the Committee decides to include a conformity assessment body in Annex 1, the Parties shall recognise the reports, certificates, authorisations and conformity marks issued by that body with effect from the date of entry into force of the decision. If the Committee decides to remove a body from Annex 1, the Parties shall recognise the reports, certificates, authorisations and conformity marks issued by that body until the date on which that decision takes effect.
Article 12
Information exchange
1. The Parties shall exchange all relevant information regarding implementation and application of the legislative, regulatory and administrative provisions listed in Annex 1.
2. Each Party shall inform the other Party of the changes it intends to make to the legislative, regulatory and administrative provisions relating to the subject matter of this Agreement and shall notify the other Party of the new provisions at least 60 days before their entry into force.
3. Where the legislation of one of the Parties stipulates that a specific item of information must be made available to the competent authority by a person established in its territory, that authority may also approach the competent authority of the other Party or enter into direct contact with the manufacturer or, if appropriate, the latter's agent in the territory of the other Party, in order to obtain that information.
4. Each Party shall immediately notify the other Party of safeguard measures taken in its territory.
Article 13
Confidentiality
Representatives, experts and other agents of the Parties shall be required, even after their duties have ceased, not to disclose information acquired under this Agreement which is of the kind covered by the obligation of professional secrecy. This information may not be used for purposes other than those envisaged by this Agreement.
Article 14
Dispute settlement
Each Party may refer any dispute relating to the interpretation or application of this Agreement to the Committee. The Committee shall endeavour to settle the dispute, and must be supplied with any information which may facilitate a thorough examination of the situation with a view to finding an acceptable solution. For that purpose, the Committee shall consider every possible means of maintaining the smooth functioning of this Agreement.
Article 15
Agreements with third countries
The Parties hereby agree that mutual recognition agreements concluded by either Party with a country that is not party to this Agreement shall in no circumstances entail an obligation upon the other Party in terms of the acceptance of manufacturer's declarations of conformity as well as of reports, certificates, authorisations and marks issued by conformity assessment bodies in that third country, unless there is an explicit agreement between the Parties.
Article 16
Annexes
The Annexes to this Agreement shall form an integral part thereof.
Article 17
Territorial application
This Agreement shall apply, as regards the Community, to the territories in which the Treaty establishing the European Community is applied under the conditions laid down in that Treaty, on the one hand, and to the territory of Switzerland, on the other.
Article 18
Revision
1. If a Party wishes to have this Agreement revised, it shall inform the Committee. Modifications to this Agreement shall enter into force after the respective internal procedures have been completed.
2. The Committee may modify Annexes 1 and 2 to this Agreement on a proposal from one of the Parties.
Article 19
Suspension
Where a Party establishes that the other Party is failing to comply with the conditions of this Agreement, it may, after consulting the Committee, suspend application of Annex 1 in full or in part.
Article 20
Acquired rights
The Parties shall continue to recognise reports, certificates, authorisations and conformity marks and manufacturers' declarations of conformity issued in accordance with, and prior to the expiry of, this Agreement, provided that the request for conformity evaluation to be started was made before the notice of non-renewal or denunciation was given.
Article 21
Entry into force and duration
1. This Agreement shall be ratified or approved by the Parties in accordance with their own procedures. It shall enter into force on the first day of the second month following the last notification of deposit of the instruments for ratification or approval of all the following seven agreements:
Agreement on the mutual recognition in relation to conformity assessment
Agreement on the free movement of persons
Agreement on air transport
Agreement on the carriage of goods and passengers by rail and road
Agreement on trade in agricultural products
Agreement on certain aspects of public procurement
Agreement on scientific and technical cooperation.
2. This Agreement shall be concluded for an initial period of seven years. It shall be tacitly extended, unless the Community or Switzerland notifies the other Party to the contrary before the expiry of that period. Where such notification is given, the provisions of paragraph 4 shall apply.
3. The Community or Switzerland may denounce this Agreement by notifying the other Party. Where such notification is given, the provisions of paragraph 4 shall apply.
4. The seven agreements referred to in paragraph 1 shall cease to apply six months after receipt of the non-renewal notice described in paragraph 2 or the denunciation notice described in paragraph 3.
Hecho en Luxemburgo, el veintiuno de junio de mil novecientos noventa y nueve.
El presente Acuerdo se establecerá por duplicado en lenguas alemana, danesa, española, finesa, francesa, griega, inglesa, italiana, neerlandesa, portuguesa y sueca y cada uno de estos textos será auténtico./Udfærdiget i Luxembourg, den enogtyvende juni nitten hundrede og nioghalvfems
i to eksemplarer på dansk, engelsk, finsk, fransk, græsk, italiensk, nederlandsk, portugisisk, spansk, svensk og tysk, idet hver af disse tekster har samme gyldighed./Geschehen zu Luxemburg am einundzwanzigsten Juni neunzehnhundertneunundneunzig
in zwei Urschriften in dänischer, deutscher, englischer, finnischer, französischer, griechischer, italienischer, niederländischer, portugiesischer, schwedischer und spanischer Sprache, wobei jeder Wortlaut gleichermaßen verbindlich ist./Έγινε στο Λουξεμβούργο, στις είκοσι μία Ιουνίου χίλια εννιακόσια ενενήντα εννέα.
Η παρούδα συμφωνία καταρτίζεται εις διπλούν στα αγγλικά, τα γαλλικά, τα γερμανικά, τα δανικά, τα ελληνικά, τα ισπανικά, τα ιταλικά, τα ολλανδικά, τα πορτογαλικά, τα σουηδικά και τα φινλανδικά, καθένα από τα κείμενα αυτά είναι αυθεντικό. /Done at Luxembourg on the twenty-first day of June in the year one thousand and ninety-nine.
This Agreement is drawn up in duplicate in the Danish, Dutch, English, Finnish, French, German, Greek, Italian, Portuguese, Spanish and Swedish languages, each text being equally authentic./Fait à Luxembourg, le vingt-et-un juin mil neuf cent quatre-vingt dix-neuf,
en double exemplaire, en langues allemande, anglaise, danoise, espagnole, finnoise, française, grecque, italienne, néerlandaise, portugaise et suédoise, chacun de ces textes faisant également foi./Fatto a Lussemburgo, addì ventuno giugno millenovecentonovantanove,
in due copie nelle lingue danese, finlandese, francese, greco, inglese, italiano, olandese, portoghese, spagnolo, svedese e tedesco; tutte facenti ugualmente fede./Gedaan te Luxemburg, de eenentwintigste juni negentienhonderd negenennegentig,
in tweevoud in de Deense, de Duitse, de Engelse, de Finse, de Franse, de Griekse, de Italiaanse, de Nederlandse, de Portugese, de Spaanse en de Zweedse taal, zijnde alle teksten gelijkelijk authentiek./Feito em Luxemburgo, em vinte e um de Junho de mil novecentos e noventa e nove,
em dois exemplares em língua alemã, inglesa, dinamarquesa, espanhola, finlandesa, francesa, grega, italiana, neerlandesa, portuguesa e sueca, todas as versões fazendo igualmente fé./Tehty Luxemburgissa kahdentenakymmenentenäensimmäusenä päivänä kesäkuuta vuonna tuhatyhdeksänsataayhdeksänkymmentäyhdeksän
kahtena kappaleena englannin, espanjan, hollannin, italian, kreikan, portugalin, ranskan, ruotsin, saksan, suomen ja tanskan kielellä, ja jokainen teksti on yhtä todistusvoimainen./Utfärdat i Luxemburg den tjugoförsta juni nittonhundranittionio
i två exemplar på det danska, engelska, finska, franska, grekiska, italienska, nederländska, portugisiska, spanska, svenska och tyska språket, vilka samtliga texter är lika giltiga.
Por la Comunidad Europea/For Det Europæiske Fællesskab/Für die Europäische Gemeinschaft/Για την Ευρωπαϊκή Κοινότητα/For the European Community/Pour la Communauté européenne/Per la Comunità europea/Voor de Europese Gemeenschap/Pela Comunidade Europeia/Euroopan yhteisön puolesta/På Europeiska gemenskapens vägnar
>PIC FILE= "L_2002114EN.037401.TIF">
>PIC FILE= "L_2002114EN.037402.TIF">
Por la Confederación Suiza
For Det Schweiziske Edsforbund
Für die Schweizerische Eidgenossenschaft
Για την Ελβετική Συνομοσπονδία
For the Swiss Confederation
Pour la Confédération suisse
Per la Confederazione svizzera
Voor de Zwitserse Bondsstaat
Pela Confederação Suíça
Sveitsin valaliiton puolesta
På Schweiziska edsförbundets vägnar
>PIC FILE= "L_2002114EN.037501.TIF">
>PIC FILE= "L_2002114EN.037502.TIF">
ANNEX 1
PRODUCT SECTORS
>TABLE>
CHAPTER 1
MACHINERY
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1 paragraph 2
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
European Community:
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 and those in Annex VII to Directive 98/37/EC.
Section V
Supplementary provisions
1. Second-hand machinery
The legislative, regulatory and administrative provisions listed in section I shall not apply to second-hand machinery.
The principle contained in Article 1paragraph 2 of this Agreement shall apply, however, to machinery legally placed on the market and/or put into service in one of the Parties and exported as second-hand machinery to the market of the other Party.
The other provisions relating to second-hand machinery, e.g. those relating to safety in the place of work in force in the importing state, shall remain applicable.
CHAPTER 2
PERSONAL PROTECTIVE EQUIPMENT
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1 paragraph 2
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 and those in Annex V to Directive 89/686/EEC.
CHAPTER 3
TOYS
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1 paragraph 1
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 and those in Annex III to Directive 88/378/EEC.
Section V
Supplementary provisions
1. Information concerning the certificate and the technical file
In accordance with Article 10(4) of Directive 88/378/EEC, the authorities listed in section III may obtain on request a copy of the certificate and, on reasoned request, a copy of the technical file and the reports on the examinations and tests carried out.
2. Notification of grounds for refusal by approved bodies
In accordance with Article 10(5) of Directive 88/378/EEC, the Swiss bodies shall inform the Swiss Federal Office of Public Health when refusing to issue an EC type-examination certificate. The Federal Office shall likewise notify the Commission of the European Communities thereof.
CHAPTER 4
MEDICAL DEVICES
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
European Community
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies listed in section II
For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and those in Annex XI to Directive 93/42/EEC, in respect of the bodies designated under that Directive, and in Annex VIII to Directive 90/385/EEC, in respect of the bodies designated thereunder.
Section V
Supplementary provisions
1. Registration of the person responsible for placing devices on the market
Any manufacturer who places on the market of one of the Parties the medical devices referred to in Article 14 of Directive 93/42/EEC shall inform the competent authorities of the Party in which he has his registered place of business of the particulars referred to in that Article. The Parties shall mutually recognise that registration. The manufacturer shall not be obliged to designate a person responsible for placing devices on the market established in the territory of the other Party.
2. Labelling of medical devices
Manufacturers of both Parties shall indicate their name or trade name and address on the label of medical devices as specified in Annex 1, point 13.3(a) to Directive 93/42/EEC. They shall not be obliged to indicate the name and address of the person responsible for placing the device on the market, of the representative or of the importer established within the territory of the other Party on the label, outer packaging or instructions for use.
3. Information exchanges
In accordance with Article 9 of the Agreement, the Parties shall in particular exchange the information referred to in Article 8 of Directive 90/385/EEC and in Article 10 of Directive 93/42/EEC.
CHAPTER 5
GAS APPLIANCES AND BOILERS
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(1)
>TABLE>
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
Provisions covered by Article 1(1)
>TABLE>
Provisions covered by Article 1(2)
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and those in Annex V to Directive 92/42/EEC, in respect of the bodies designated under that Directive, and in Annex V to Directive 90/396/EEC, in respect of the bodies designated thereunder.
CHAPTER 6
PRESSURE VESSELS
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(1)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
European Community:
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 and those in Annex III to Directive 87/404/EEC.
Section V
Supplementary provisions
Recognition of certificates by Switzerland
Where the provisions of Swiss legislation listed in section I lay down a conformity assessment procedure, Switzerland shall recognise certificates issued by a designated Community body listed in section II which certifies that the product conforms to standard EN 286.
CHAPTER 7
TELECOMMUNICATIONS TERMINAL EQUIPMENT
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
European Community
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, designating authorities shall comply with the general principles contained in Annex 2 and those in Annex V to Directive 98/13/EC.
Section V
Supplementary provisions
1. Administrative Decision
The two Parties shall mutually recognise the administrative Decision (Art. 11(6), Directive 98/13/EC + Art. 31 of the Federal Law of 30 April 1997 on telecommunications (LTC; RO 1977 2187) and Article 8/6 of the Federal Council Order of 6.10.97 on telecommunications installations (ITU; RO 1997 2853) approving connection of the terminal equipment concerned to the public telecommunications network.(1).
2. Notification of the manufacturer's or supplier's declaration
When placing on the market of one of the Parties the telecommunications equipment referred to in Article 3(1) of Directive 98/13/EC, the person responsible shall notify the manufacturer's or supplier's declaration to the notified body of the Party where the equipment is first placed on the market.
3. Test laboratories
Each Party shall notify the other of the test laboratories designated to carry out the tests pertaining to the procedures referred to in Article 10 of Directive 98/13/EC. The criteria fixed by the relevant harmonised standards for the designation of such laboratories shall be applied.
4. Exchanges of information between conformity assessment bodies
4.1 In accordance with Annex I, point 7f of Directive 98/13/EC, the conformity assessment bodies listed in section II of this Annex shall make available to the other bodies the relevant information concerning type-examination certificates issued and withdrawn.
4.2 In accordance with Annex III, point 6, and Annex IV, point 6 of Directive 98/13/EC, the conformity assessment bodies listed in section II of this Annex shall make available to the other bodies the relevant information concerning quality system approvals issued and withdrawn.
CHAPTER 8
EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, designating authorities shall comply with the general principles contained in Annex 2 and those in Annex XI to Directive 94/9/EC.
Section V
Supplementary provisions
1. Information exchange
The conformity assessment bodies listed in section II shall provide the Member States, the competent Swiss authorities and/or the other conformity assessment bodies with the information provided for in Article 9(2) of Directive 76/117/EEC.
2. Technical documentation
It shall be sufficient for manufacturers, their authorised representatives or the person responsible for placing products on the market to hold the technical documents required by the national authorities for inspection purposes at their disposal in the territory of one of the Parties for a period of at least ten years after the last date of manufacture of the product.
The Parties hereby undertake to forward all relevant technical documents at the request of the authorities of the other Party.
CHAPTER 9
ELECTRICAL EQUIPMENT AND ELECTROMAGNETIC COMPATIBILITY
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
European Community
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, designating authorities shall comply with the general principles contained in Annex 2 and those in Annex II to Directive 89/336/EEC.
Section V
Supplementary provisions
1. Technical documentation
It shall be sufficient for manufacturers, their authorised representatives or the person responsible for placing products on the market to hold the technical documents required by the national authorities for inspection purposes at their disposal in the territory of one of the Parties for a period of at least ten years after the last date of manufacture of the product.
The Parties hereby undertake to forward all relevant documents at the request of the authorities of the other Party.
2. Standardisation bodies
In accordance with Article 11 of Directive 73/23/EEC, the Parties shall notify each other of the bodies responsible for drawing up the standards referred to in Article 5 of this Directive.
3. Competent bodies
The Parties shall inform each other of and mutually recognise the bodies made responsible for drawing up technical reports and/or certificates pursuant to Article 8(2) of Directive 73/23/EEC and Article 10(2) of Directive 89/336/EEC.
4. Special measures
In accordance with Article 6(2) of Directive 89/336/EEC, each Party shall inform the other of the special measures taken pursuant to paragraph 1 of that Article.
5. Competent authorities
In accordance with Article 10(6) of Directive 89/336/EEC, each Party shall notify the other of the competent authorities referred to in that Article.
CHAPTER 10
CONSTRUCTION PLANT AND EQUIPMENT
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(1)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, designating authorities shall comply with the general principles contained in Annex 2 and those in Annex II to Council Directive 84/532/EEC, as amended by Council Directive 88/665/EEC.
CHAPTER 11
MEASURING INSTRUMENTS AND PREPACKAGES
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(1)
>TABLE>
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.
Section III
Designating authorities
Provisions covered by Article 1(1)
>TABLE>
Provisions covered by Article 1(2)
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, designating authorities shall comply with the general principles contained in Annex 2 and those in Annex V to Directive 90/384/EEC, as regards the products covered by that Directive.
Section V
Supplementary provisions
1. Information exchange
The conformity assessment bodies listed in section II shall periodically provide the Member States and the competent Swiss authorities with the information provided for in point 1.5 of Annex II to Directive 90/384/EEC.
The conformity assessment bodies listed in section II may request the information provided for in point 1.6 of Annex II to Directive 90/384/EEC.
2. Prepackages
Switzerland shall recognise checks carried out in accordance with the provisions of Community legislation listed in section I by a Community body listed in section II in the case of Community prepackages placed on the market in Switzerland.
As regards statistical checking of the quantities declared on prepackages, the European Community shall recognise the Swiss method laid down in Articles 24 to 40 of the "Ordonnance sur les déclarations" (RS 941.281.1) as equivalent to the Community method laid down in Annex II of Directives 75/106/EEC and 76/211/EEC, as amended by Directive 78/891/EEC. Swiss producers whose prepackages conform to Community legislation and have been checked according to the Swiss method shall affix the "e" mark on their products exported to the EC.
CHAPTER 12
MOTOR VEHICLES
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the authorities responsible for type-approval, technical services and testing bodies.
European Community:
Switzerland:
Authority responsible for type-approval
Swiss Federal Roads Office
Section des homologations
CH - 3003 Berne
Section III
Designating authorities
European Community
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, the designating authorities shall refer to their respective legislative, regulatory and administrative provisions as listed in section I.
Section V
Supplementary provisions
The provisions of this section shall apply exclusively to relations between Switzerland and the Community.
1. Information exchange
The competent type-approval authorities in Switzerland and the Member States shall in particular exchange the information referred to in Article 4(5) and (6) of Directive 70/156/EEC, as amended by Directive 92/53/EEC and as last adapted to technical progress by Commission Directive 98/14/EC.
In the event of refusal by Switzerland or the Member States to grant type-approval in accordance with Article 4(2) of Directive 70/156/EEC, as amended by Directive 92/53/EEC, and as last adapted to technical progress by Commission Directive 98/14/EC, their competent authorities shall notify each other of their decision and give the reasons for it. The competent Swiss authority shall likewise inform the Commission thereof.
2. Recognition of vehicle type-approval
Switzerland shall also recognise vehicle type-approval granted before the entry into force of this Agreement in accordance with Directive 70/156/EEC, as amended by Directive 92/53/EEC, and as last adapted to technical progress by Commission Directive 98/14/EC, by the authorities responsible for type-approval listed in section II of this Chapter where that approval is still valid in the EC.
The European Community shall recognise Swiss type-approval where Switzerland's requirements are deemed to be equivalent to those of Directive 70/156/EEC, as amended by Directive 92/53/EEC, and as last adapted to technical progress by Commission Directive 98/14/EC.
Recognition of Swiss-issued type-approval shall be suspended should Switzerland fail to adapt its legislation to all the Community type-approval legislation in force.
3. Vehicle type-approval safeguard clauses
Registration and entry into service
1. Each Member State and Switzerland shall register, permit the sale or entry into service of new vehicles on grounds relating to their construction and functioning if, and only if, they are accompanied by a valid certificate of conformity. In the case of incomplete vehicles, each Member State and Switzerland may not prohibit the sale of such vehicles but may refuse their permanent registration and entry into service so long as they are not completed.
2. Each Member State and Switzerland shall permit the sale or entry into service of components or separate technical units if, and only if, they comply with the requirements of the relevant separate Directive or the requirements of the Swiss legislation equivalent to the relevant separate Directive.
3. If a Member State or Switzerland finds that vehicles, components or separate technical units of a particular type are a serious risk to road safety although they are accompanied by a valid certificate of conformity or are properly marked, it may, for a maximum period of six months, refuse to register such vehicles or may prohibit the sale or entry into service in its territory of such vehicles, components or separate technical units. It shall forthwith notify the other Member States, Switzerland and the Commission thereof, stating the reasons on which its decision is based. If the Member State or Switzerland which granted type-approval disputes the risk to road safety notified to it, the Member States or Switzerland concerned shall endeavour to settle the dispute. The Commission and the Committee shall be kept informed and shall, where necessary, hold appropriate consultations for the purpose of reaching a settlement.
Measures related to the conformity of production
1. When a Member State or Switzerland grants type-approval, it shall take the necessary measures in accordance with Annex X to Framework Directive 70/156/EEC, as amended by Directive 92/53/EEC, and as last adapted to technical progress by Commission Directive 98/14/EC, in relation to that approval to verify, if need be in cooperation with the approval authorities of the other Member States or Switzerland, that adequate arrangements have been made to ensure that vehicles, systems, components or separate technical units produced, conform to the approved type.
2. When a Member State or Switzerland has granted a type approval, it shall take the necessary measures in accordance with Annex X to Framework Directive 70/156/EEC, as amended by Directive 92/53/EEC, and as last adapted to technical progress by Commission Directive 98/14/EC, in relation to that approval to verify, if need be in cooperation with the approval authorities of the other Member States or Switzerland, that the arrangements referred to in paragraph 1 continue to be adequate and that vehicles, systems, components or separate technical units produced, continue to conform to the approved type. Verification to ensure that products conform to the approved type shall be limited to the procedures set out in section 2 of Annex X to Framework Directive 70/156/EEC, as amended by Directive 92/53/EEC, and as last adapted to technical progress by Commission Directive 98/14/EC, and in those separate Directives that contain specific requirements.
Nonconformity with the approved type
1. There shall be failure to conform to the approved type where deviations from the particulars in the type-approval certificate and/or the information package are found to exist and where these deviations have not been authorised under Article 5 (3) or (4), by the Member States or Switzerland which granted the type-approval. A vehicle shall not be considered to deviate from the approved type where tolerances are permitted by separate Directives and these tolerances are respected.
2. Where a Member State or Switzerland has granted type-approval and finds that vehicles, components or separate technical units accompanied by a certificate of conformity or bearing an approval mark do not conform to the type it has approved, it shall take the necessary measures to ensure that vehicles, components or separate technical units produced again conform to the approved type. The approval authorities of that Member State or Switzerland shall notify those of the other Member States and/or Switzerland of the measures taken which may extend to withdrawal of type-approval.
3. If a Member State or Switzerland demonstrates that vehicles, components or separate technical units accompanied by a certificate of conformity or bearing an approval mark do not conform to the approved type, it may request the Member State or Switzerland which granted the type-approval to verify that vehicles, components or separate technical units produced conform to the approved type. Such action shall be taken as soon as possible and in any case within six months of the date of the request.
4. In the case of:
- a vehicle type-approval where the nonconformity of a vehicle arises exclusively from the nonconformity of a system, component or separate technical unit, or
- a multi-stage type-approval where the nonconformity of a completed vehicle arises exclusively from the nonconformity of a system, component or separate technical unit being part of the incomplete vehicle, or of the incomplete vehicle itself, the vehicle-approval authority shall request the Member State(s) or Switzerland which granted any relevant system, component, separate technical unit or incomplete vehicle type-approval(s) to take the necessary action to ensure that vehicles produced again conform to the approved type. Such action shall be taken as soon as possible and in any case within six months of the date of the request, if necessary in conjunction with the Member State or Switzerland making the request.
Where a failure to conform is established, the approval authorities of the Member State or Switzerland which granted the system, component or separate technical unit type-approval or the approval of the incomplete vehicle shall take the measures set out in paragraph 2 of Directive 70/156/EEC, as amended by Directive 92/53/EEC, and as last adapted to technical progress by Commission Directive 98/14/EC.
5. The approval authorities of the Member States or Switzerland shall inform each other within one month of any withdrawal of type-approval and of the reasons for such a measure.
6. If the Member State or Switzerland which granted type-approval disputes the failure to conform notified to it, the Member States concerned and Switzerland shall endeavour to settle the dispute. The Commission and the Committee shall be kept informed and shall, where necessary, hold appropriate consultations for the purpose of reaching a settlement.
CHAPTER 13
AGRICULTURAL OR FORESTRY TRACTORS
Section I
Legislative, regulatory and administrative provisions
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the authorities responsible for type-approval, technical services and testing bodies.
European Community
Switzerland
Authority responsible for type-approval
Swiss Federal Roads Office CH - 3003 Berne
Section III
Designating authorities
European Community
>TABLE>
Section IV
Special rules relating to the designation of conformity assessment bodies
For the designation of conformity assessment bodies, the designating authorities shall refer to their respective legislative, regulatory and administrative provisions as listed in section I.
Section V
Supplementary provisions
Information exchange
The competent Member State's and Swiss authorities shall notify each other of conforming (Art. 5 and 6, Directive 74/150/EEC) or non-conforming (Art. 8, Directive 74/150/EEC) vehicles, devices and systems placed on the market.
CHAPTER 14
GOOD LABORATORY PRACTICE (GLP)
Scope and coverage
The provisions of this Chapter shall apply to the testing of chemicals according to GLP, being either substances or preparations, covered by the legislative, regulatory and administrative provisions listed in section I. For the purposes of this Chapter the provisions of Article 4 of this Agreement concerning origin do not apply.
Unless specific definitions are given, the definition of terms in the "OECD Principles of Good Laboratory Practice" [Appendix II to OECD Council Decision of 12 May 1981 C(81)30(Final)], the "Guides for Compliance Monitoring Procedures for Good Laboratory Practice" [Appendix I to Council Decision-Recommendation of 2 October 1989 C(89)87(Final)] and GLP Consensus documents, OECD Series on Principles of Good Laboratory Practice and Compliance Monitoring, and all amendments made thereto, shall apply.
The Parties recognise the equivalence of each other's compliance monitoring programmes on Good Laboratory Practice that are in accordance with the OECD decisions and recommendations mentioned above and the legislative, regulatory and administrative procedures and principles listed in section IV.
The Parties mutually accept studies and data generated therefrom, produced by the test facilities of the other Party listed in section II provided they participate in the Good Laboratory Practice compliance monitoring programme of that Party in accordance with the principles and provisions stated above.
The Parties mutually accept the conclusions of study audits and test facility inspections performed by the monitoring authorities referred to in section III.
Section I
Legislative, regulatory and administrative provisions
With regard to the testing of chemicals according to GLP, the relevant parts of the legislative, regulatory and administrative provisions listed below shall apply.
Provisions covered by Article 1(1)
>TABLE>
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
For the purpose of this Sectoral Chapter, "Conformity Assessment Bodies" means the test facilities recognised under each Party's GLP monitoring programme.
On the basis of information provided by the Parties according to Section V of this Chapter, the Committee referred to in Article 10 of this Agreement shall establish and keep up to date, according to the procedure described in Article 11 of this Agreement, a list of the test facilities that have been found to be in conformity with the GLP principles.
Section III
Designating authorities
For the purpose of this Sectoral Chapter, "Designating Authorities" means the official GLP Monitoring Authorities of the Parties.
European Community:
>TABLE>
Switzerland:
Environmental studies on all products
Federal Office of Environment, Forests and Landscape
CH-3003 Berne
Health studies on pharmaceutical products
Intercantonal Office for the Control of Medicines
Erlachstraße 8
PO Box
CH-3000 Berne 9
Health studies on all products except pharmaceuticals
Federal Office of Public Health
Chemicals division
CH-3003 Berne
Section IV
Special principles for designating conformity assessment bodies
For the purpose of this Sectoral Chapter, "designation of conformity assessment bodies" means the procedure by which the GLP Monitoring Authorities recognise that test facilities comply with the GLP principles. To this end they shall apply the principles and procedures of their provisions listed below, that are recognised to be equivalent and in conformity with the aforementioned OECD Council Acts C(81) 30 Final and C(89) 87 Final:
>TABLE>
Section V
Additional provisions
1. Information exchange
In accordance with Article 12 of this Agreement, the Parties in particular provide each other at least annually with a list of the test facilities which, in the light of the results of the inspections and study audits, conform to Good Laboratory Practice, as well as of the dates of inspection or audit and their compliance status.
In accordance with Article 6 of the Agreement, the Parties shall inform each other in a timely manner when a test facility coming under the terms of section II of this sectoral Chapter which states that it applies Good Laboratory Practice fails to conform to such practice to an extent which may jeopardise the integrity or authenticity of any such studies it conducts.
The Parties shall supply each other with any additional information on a test facility inspection or study audit in response to a reasonable request from the other Party.
2. Test Facility Inspections
Each Party may request further test facility inspection or study audits if there is a documented doubt as to whether a test was conducted in accordance with Good Laboratory Practice.
If, in exceptional cases, doubts persist and the requesting Party can justify special concern, it may, in accordance with Article 8 of the Agreement, designate one or more experts of its authorities listed in section III to participate in a laboratory inspection or the audit of a study conducted by the authorities of the other Party.
3. Confidentiality
In conformity with Article 13 of the Agreement, the Parties shall keep confidential any information brought to their knowledge pursuant to this Sectoral Chapter or that came to their knowledge in the framework of participation in an inspection or study audit and which falls within the definition of a trade secret or confidential commercial or financial information. They shall treat such information with at least the same confidentiality as that accorded to it by the providing Party and ensure that any authority to whom the information is transmitted treats it in the same way.
4. Cooperation
Based on Article 9 of the Agreement, each Party may, on request, participate as an observer in an inspection of a test facility conducted by the authorities of the other Party with the consent of the test facility concerned in order to maintain a continuing understanding of the other Party's inspection procedures.
CHAPTER 15
MEDICINAL PRODUCTS GMP INSPECTION AND BATCH CERTIFICATION
Scope and coverage
The provisions of this Sectoral Chapter cover all medicinal products which are industrially manufactured in Switzerland or the European Community, and to which Good Manufacturing Practice (GMP) requirements apply.
For medicinal products covered by this Chapter, each party shall recognise the conclusions of inspections of manufacturers carried out by the relevant inspection services of the other Party and the relevant manufacturing authorisations granted by the competent authorities of the other Party.
The manufacturer's certification of the conformity of each batch to its specifications shall be recognised by the other Party without recontrol at import.
In addition, official batch releases carried out by an authority of the exporting Party will be recognised by the other Party.
"Medicinal products" means all products regulated by pharmaceutical legislation in the European Community and Switzerland as listed in Section I of this Chapter. The definition of medicinal products includes all human and veterinary products, such as chemical and biological pharmaceuticals, immunologicals, radio-pharmaceuticals, stable medicinal products derived from human blood or human plasma, pre-mixes for the preparation of veterinary medicated feedingstuffs and, where appropriate, vitamins, minerals, herbal remedies and homeopathic medicinal products.
"GMP" is that part of quality assurance which ensures that products are consistently produced and controlled to the quality standards appropriate to their intended use and as required by the marketing authorisation and products specifications. For the purpose of this Chapter it includes the system whereby the manufacturer receives the specification of the product and the process from the marketing authorisation holder or applicant and ensures that the medicinal product is made in compliance with this specification (Equivalent to "Qualified Person" for certification in the EC).
With respect to medicinal products covered by the legislation of one Party but not the other, the manufacturing company can request, for the purpose of this Agreement, an inspection be made by the locally competent inspection service. This provision shall apply i.a. to the manufacture of active pharmaceutical ingredients, intermediate products and investigational medicinal products, as well as to pre-marketing inspections. Operational arrangements are detailed under section III, paragraph 3.
Certification of manufacturers
At the request of an exporter, importer or the competent authority of the other Party, the authorities responsible for granting manufacturing authorisations and for supervision of the manufacture of medicinal products shall certify that the manufacturer:
- is appropriately authorised to manufacture the relevant medicinal product, or to carry out the relevant specified manufacturing operation
- is regularly inspected by the authorities
- complies with the national GMP requirements recognised as equivalent by the two parties, and which are listed in Section I of this Chapter. Should different GMP requirements be used as reference, this is to be mentioned in the certificate.
The certificates shall also identify the site(s) of manufacture (and contract quality control laboratories, if any).
Certificates shall be issued expeditiously, and the time taken should not exceed thirty calendar days. In exceptional cases, i.a. when a new inspection has to be carried out, this period may be extended to sixty days.
Batch certification
Each batch exported shall be accompanied by a batch certificate established by the manufacturer (self-certification) after a full qualitative analysis, a quantitative analysis of all the active ingredients and all the other tests or checks necessary to ensure the quality of the product in accordance with the requirements of the marketing authorisation. This certificate shall attest that the batch meets its specifications and shall be kept by the importer of the batch. It will be made available upon request of the competent authority.
When issuing a certificate, the manufacturer shall take account of the provisions of the current WHO certification scheme on the quality of pharmaceutical products moving in international commerce. The certificate shall detail the agreed specifications of the product, the reference of the analytical methods and the analytical results. It shall contain a statement that the batch processing and packaging records were reviewed and found in conformity with GMP. The batch certificate shall be signed by the person responsible for releasing the batch for sale or supply, i.e. in the European Community the "qualified person" referred to in Article 21 of Directive 75/319/EEC, and in Switzerland the responsible person referred to in Articles 4 and 5 of the Ordinance on immunobiological products, Articles 4 and 5 of the Ordinance on immunobiological products for veterinary use and Article 10 of the Directives of the IOCM on the manufacture of medicinal products.
Official Batch Release
When an official batch release procedure applies, official batch releases carried out by an authority of the exporting Party (listed in section II) will be recognised by the other Party. The manufacturer shall provide the certificate of the official batch release.
For the Community, the official batch release procedure is specified in document "Control/Authority Batch Release of Vaccination and Blood Products of 24 September 1998" and different specific batch release procedures. For Switzerland, the official batch release procedure is specified in Articles 22-27 of the Ordinance on immunobiological products, Articles 20-25 of the Ordinance on immunobiological products for veterinary use and Articles 4-6 of the Directives of the IOCM on the Authority Batch Release.
Section I
With regard to GMP, the relevant parts of the legislative, regulatory and administrative provisions listed below apply. However, the reference quality requirements of products to be exported, including their manufacturing method and product specifications, shall be those of the relevant marketing authorisation granted by the competent authority of the importing Party.
Provisions covered by Article 1(2)
>TABLE>
Section II
Conformity assessment bodies
For the purpose of this Chapter "Conformity Assessment Bodies" means the official GMP inspection services of each Party.
European Community
- Germany
Bundesministerium für Gesundheit
Am Propsthof 78a
D-53108 Bonn
Tel. (49-228) 941 23 40
Fax (49-228) 941 49 23
for immunologicals:
Paul-Ehrlich-Institut, Federal Agency for Sera & Vaccines
Postfach/PO Box
D-63207 Langen
Tel. (49-610) 377 10 10
Fax (49-610) 377 12 34
- Austria
Bundesministerium für Gesundheit und Konsumentenschuzt
Radetzkystrasse 2
A-1031 Wien
Tel. (43-1) 711 72 46 42
Fax (43-1) 714 92 22
- Belgium
Inspection générale de la Pharmacie/Algemene Farmaceutische Inspectie
Cité administrative de l'État/Rijksadministratief Centrum
Quartier Vésale/Vesalius Gebouw
B-1010 Bruxelles/Brussel
Tel. (32-2)210 49 24
Fax (32-2)210 48 80
- Denmark
Sundhedsstyrelsen Medicines Division
Frederikssundsvej 378
DK-2700 Brønshøj
Tel. (45) 44 88 93 20
Fax (45) 42 84 70 77
- Spain
Ministerio de Sanidad y Consumo
Subdirección General de Control Farmaceutico
Paseo del Prado 18-20
E-28014 Madrid
Tel. (34-1) 596 40 68
Fax (34-1) 596 40 69
- Finland
National Agency for Medicines
PO Box 278
FIN-00531 Helsinki
Tel. (358-0) 396 72 112
Fax (358-0) 71 44 69
- France
for medicinal products for human use
Agence du Médicament
143-145 boulevard Anatole France
F-93200 Saint-Denis
Tel. (33) 148 13 20 00
Fax (33) 148 13 24 78
for veterinary medicinal products
Agence Nationale du Médicament Véterinaire la haute Marche - Javené
F-35133 Fougères
Tel. (33) 9 994 78 78
Fax (33) 9 994 78 99
- Greece
National Drug Organization (EOF)
Mesogion 284
GR-Athens 15562
Tel. (30-1) 654 55 30
Fax (30-1) 654 95 91
- Ireland
National Drugs Advisory Board
63-64 Adelaide Road
Dublin 2
Ireland
Tel. (353-1) 676 49 71-7
Fax (353-1) 676 78 36
- Italy
Ministero della Sanità
Direzione generale del servizio farmaceutico
Viale della Civiltà Romana 7
I-00144 Roma
Tel. (39) 06-59 94 36 76
Fax (39) 06-59 94 33 65
- Luxembourg
Division de la Pharmacie et des Médicaments
10 rue C.M. Spoo
L-2546 Luxembourg
Tel. (352) 47 85 590/93
Fax (352) 22 44 58
- Netherlands
Ministerie van Volksgezondheid, Welzijn en Sport
Inspectie voor de Gezondheidszorg
Postbus 5406
2280 HK Rijswijk
Netherlands
Tel. (31-70) 340 79 11
Fax (31-70) 340 51 77
- Portugal
Instituto Nacional da Farmácia e do Medicamento - INFARMED
Av. do Brasil, 53
P-1700 Lisboa
Tel. (351-1) 795
Fax (351-1) 795 91 16
- United Kingdom
for human and veterinary (non immunologicals):
Medicines Control Agency
1 Nine Elms Lane
London SW8 5NQ
United Kingdom
Tel. (44-171) 273 05 00
Fax (44-171) 273 06 76
for veterinary immunologicals
Veterinary Medicines Directorate
Woodham Lane
New Haw, Addlestone
Surrey KT15 3NB
United Kingdom
Tel. (44-193) 233 69 11
Fax (44-193) 233 66 18
- Sweden
Läkemedelsverket - Medical Products Agency
Husargatan, 8
Box 26
S-75103 Uppsala
Tel. (46-18) 17 46 00
Fax (46-18) 54 85 66
Switzerland
Swiss Federal Office of Public Health, Division of Biologicals, CH-3003 Berne (for immunobiological products for human use)
Institute for Virology and Immunoprophylaxis, Research Station of the Swiss Federal Veterinary Office, CH-3147 Mittelhäusern (for immunobiological products for veterinary use)
Intercantonal Office for the Control of Medicines, CH-3000 Berne 9 (for all other medicinal products for human and veterinary use)
Section III
Additional provisions
1. Transmission of inspection reports
Upon reasoned request, the relevant inspection services shall forward a copy of the last inspection report of the manufacturing site or, in case analytical operations are contracted out, of the control site. The request may concern a "full inspection report" or a "detailed report" (see item 2 below). Each party shall deal with these inspection reports with the degree of confidentiality requested by the providing Party.
Parties will ensure that inspection reports are forwarded in no more than 30 calendar days, this period being extended to 60 days should a new inspection be carried out.
2. Inspection reports
A "full inspection report" comprises a Site Master File (compiled by the manufacturer or by the inspectorate) and a narrative report by the inspectorate. A "detailed report" responds to specific queries about a firm by the other Party.
3. GMP Reference
(a) Manufacturers shall be inspected against the applicable GMP of the exporting party (see section I).
(b) With respect to medicinal products covered by the pharmaceutical legislation of the importing Party but not the exporting one, the locally competent inspection service willing to carry out an inspection of the relevant manufacturing operations shall inspect against its own GMP or, in the absence of specific GMP requirements, against the applicable GMP of the importing Party.
For specific products or classes of products (e.g. investigational medicinal products, starting materials not limited to active pharmaceutical ingredients), equivalence of GMP requirements shall be determined according to a procedure established by the Committee.
4. Nature of inspections
(a) Inspections shall routinely assess the compliance of the manufacturer with GMP. These are called general GMP inspections (also regular, periodic, or routine inspections).
(b) "Product- or process-oriented" inspections (which may be "pre-marketing" inspections as relevant) focus on the manufacture of one or a series of product(s) or process(es) and include an assessment of the validation of and compliance with specific process or control aspects as described in the marketing authorisation. Where necessary, relevant product information (the quality dossier of an application/authorisation dossier) shall be provided in confidence to the inspectorate.
5. Fees
The regime of inspection/establishment fees is determined by the manufacturer's location. Inspection/establishment fees shall not be charged to manufacturers located on the territory of the other Party.
6. Safeguard clause for inspections
Each Party reserves the right to have its own inspection conducted for reasons identified to the other Party. Such inspections are to be notified in advance to the other Party and shall, in accordance with Article 8 of the Agreement, be carried out jointly by the competent authorities of the two Parties. Recourse to this safeguard clause should be an exception.
7. Exchange of information between authorities and approximation of quality requirements
In accordance with the general provisions of the Agreement, the parties shall exchange any information necessary for the mutual recognition of inspections.
The relevant authorities in Switzerland and in the Community shall also keep each other informed of any new technical guidance or inspection procedure. Each party shall consult the other before their adoption and shall endeavour to proceed towards their approximation.
8. Inspectors training
In accordance with Article 9 of the Agreement, training sessions for inspectors, organised by the authorities, shall be accessible to inspectors of the other Party. The Parties to the Agreement shall keep each other informed on these sessions.
9. Joint Inspections
In accordance with Article 12 of the Agreement, and by mutual agreement between the Parties, joint inspections may be organised. These inspections are intended to develop common understanding and interpretation of practice and requirements. The setting up of these inspections and their form shall be agreed through procedures approved by the Committee established under Article 10 of the Agreement.
10. Alert system
Contact points shall be agreed between both Parties to permit authorities and manufacturers to inform the authorities of the other Party with the appropriate speed in case of quality defect, batch recalls, counterfeiting and other problems concerning quality, which could necessitate additional controls or suspension of the distribution of the batch. A detailed alert procedure shall be agreed.
The Parties shall ensure that any suspension or withdrawal (total or partial) of a manufacturing authorisation, based on non-compliance with GMP and which could have public health implications, are communicated to each other with the appropriate degree of urgency.
11. Contact points
For the purpose of this Agreement, the contact points for any technical question, such as exchanges of inspection reports, inspectors training sessions, technical requirements, are:
for the EC
the Director of the European Agency for the Evaluation of Medicinal Products and
for Switzerland
the official GMP inspection services listed in Section II above.
12. Divergence of views
Both Parties shall use their best endeavours to resolve any divergence of views concerning inter alia compliance of manufacturers and conclusions of inspection reports. Unresolved divergences of view will be referred to the Committee as established under Article 10 of the Agreement.
(1) In the context of this Agreement, the expression "public telecommunications network" is to be interpreted for the purpose of Swiss law as "installations provided by a telecommunications services provider".
ANNEX 2
GENERAL RULES REGARDING THE DESIGNATION OF CONFORMITY ASSESSMENT BODIES
A. General terms and conditions
1. Under this Agreement, the designating authorities shall remain solely responsible for the competence and the capacity of the bodies they have designated and shall designate only legally identifiable bodies under their jurisdiction.
2. Designating authorities shall designate conformity assessment bodies able to demonstrate by objective means that they understand and have the requisite experience and competence to apply the requirements and certification procedures laid down in the legislative, regulatory and administrative provisions referred to in Annex I, that are applicable to the specific product, product category or sector for which they are designated.
3. Demonstration of technical competence shall cover:
- the conformity assessment body's technical knowledge of the relevant products, processes or services which it is willing to treat;
- the understanding of the technical standards and/or legislative, regulatory and administrative provisions for which designation is sought;
- the physical capability to perform a given conformity assessment activity;
- the adequate management of the activity concerned; and
- any other circumstance necessary to give assurance that the conformity assessment activity will be adequately performed at all times.
4. The technical competence criteria shall be based as far as possible on internationally accepted documents, such as the EN 45000 series of standards or equivalents as well as on supplemented interpretative documents as appropriate. However these documents clearly need to be interpreted in such a way as to take account of the different types of requirements laid down in the applicable legislative, regulatory and administrative provisions.
5. The Parties shall encourage harmonisation of designation procedures and coordination of conformity assessment procedures through cooperation between designating authorities and conformity assessment bodies based on coordination meetings, participation in mutual recognition arrangements, and ad hoc working party meetings. The Parties shall also encourage accreditation bodies to participate in mutual recognition arrangements.
B. System for verification of conformity assessment bodies' competence
6. In order to verify the technical competence of conformity assessment bodies, the authorities concerned may use various procedures ensuring an appropriate level of trust between the Parties. If necessary, a Party shall indicate to the designating authority possible ways of demonstrating competence.
(a) Accreditation
Accreditation shall constitute a presumption of the technical competence of conformity assessment bodies in relation to the application of the requirements of the other Party provided that the competent accreditation body:
- complies with the relevant international provisions in force (EN 45000 standards or ISO/IEC guides); and
- is signatory to multilateral arrangements under which it is subject to peer evaluation, or
- takes part, under the authority of a Designating Authority, and in accordance with whatever conditions are decided on, in programmes to conduct comparisons and exchange technical experience, in the interests of ensuring continued trust in the technical competence of the accreditation and conformity-assessment bodies. Such programmes could include joint evaluations, special cooperation exercises or conformity assessment.
Where the criteria applicable to conformity assessment bodies require the latter to assess the conformity of products, processes or services directly to standards or technical specifications, the designating authorities may use accreditation as a presumption of the conformity assessment body's technical competence provided that it enables assessment of those bodies' ability to apply such standards or technical specifications. Designation shall be limited to those activities of the conformity assessment body.
Where the criteria applicable to conformity assessment bodies require the latter to assess the conformity of products, processes or services not directly to standards or technical specifications, but to general (essential) requirements, the designating authorities may use accreditation as a presumption of the conformity assessment body's technical competence provided that it incorporates elements which will enable assessment of the capacity of the conformity assessment body (technical knowledge of the product, of its use, etc.) to assess the conformity of the product to those essential requirements. Designation shall be limited to those activities of the conformity assessment body.
(b) Other means
If there is no accreditation scheme, or on other grounds, the authorities concerned shall require the conformity assessment bodies to demonstrate their competence by other means, e.g.:
- participation in regional or international mutual recognition arrangements or certification systems;
- regular peer evaluation, based on clear criteria and conducted with the appropriate expertise;
- aptitude tests; or
- comparison of conformity assessment bodies.
C. Evaluation of the verification system
7. Once a verification system to evaluate the competence of conformity assessment bodies has been defined, the other Party will be invited to check that the system guarantees the conformity of the designation process to its own legal requirements. Such checks shall focus on the appropriateness and effectiveness of the verification system rather than on the conformity assessment bodies themselves.
D. Formal designation
8. When the Parties submit their proposals to the Committee on the inclusion of conformity assessment bodies in the Annexes, they shall provide the following details in respect of each body:
(a) its name;
(b) its postal address;
(c) its fax number;
(d) the Sectoral Chapter, product categories or products, processes and services covered by the designation;
(e) the conformity assessment procedures covered by the designation;
(f) the methods used to establish the body's competence.
Final Act
The plenipotentiaries
of the "EUROPEAN COMMUNITY",
and
of the SWISS CONFEDERATION,
meeting on the twenty-first day of June in the year one thousand nine hundred and ninety-nine in Luxembourg for the signature of the Agreement between the European Community and the Swiss Confederation on mutual recognition in relation to conformity assessment have adopted the Joint Declarations mentioned below and attached to this Final Act:
Joint Declaration by the Contracting Parties on the revision of Article 4,
Joint Declaration on the mutual recognition of good clinical practice and inspections relating thereto,
Joint Declaration by the Contracting Parties on updating the Annexes,
Joint Declaration on further negotiations.
They also took note of the following Declaration annexed to this Final Act:
Declaration on Swiss attendance of Committees,
Hecho en Luxemburgo, el día ventiuno de junio del año mil novecientos noventa y nueve.
Udfærdiget i Luxembourg, den enogtyvende juni nitten hundrede og nioghalvfems.
Geschehen zu Luxemburg am einundzwanzigsten Juni neunzehnhundertneunundneunzig.
Έγινε στο Λουξεμβούργο, στις είκοσι μία Ιουνίου χίλια εννιακόσια ενενήντα εννέα.
Done at Luxembourg on the twenty-first day of June in the year one thousand nine hundred and ninety-nine.
Fait à Luxembourg, le vingt-et-un juin mil neuf cent quatre-vingt dix-neuf.
Fatto a Lussemburgo, addì ventuno giugno millenovecentonovantanove.
Gedaan te Luxemburg, de eenentwintigste juni negentienhonderd negenennegentig.
Feito no Luxemburgo, em vinte e um de Junho de mil novecentos e noventa e nove.
Tehty Luxemburgissa kahdentenakymmenentenäensimmäisenä päivänä kesäkuuta vuonna tuhatyhdeksänsataayhdeksänkymmentäyhdeksän.
Som gjordes i Luxemburg den tjugoförsta juni nittonhundranittionio.
Por la Comunidad Europea/For Det Europæiske Fællesskab/Für die Europäische Gemeinschaft/Για την Ευρωπαϊκή Κοινότητα/For the European Community/Pour la Communauté européenne/Per la Comunità europea/Voor de Europese Gemeenschap/Pela Comunidade Europeia/Euroopan yhteisön puolesta/På Europeiska gemenskapens vägnar
>PIC FILE= "L_2002114EN.042701.TIF">
>PIC FILE= "L_2002114EN.042702.TIF">
Por la Confederación Suiza
For Det Schweiziske Edsforbund
Für die Schweizerische Eidgenossenschaft
Για την Ελβετική Συνομοσπονδία
For the Swiss Confederation
Pour la Confédération suisse
Per la Confederazione svizzera
Voor de Zwitserse Bondsstaat
Pela Confederação Suíça
Sveitsin valaliiton puolesta
På Schweiziska edsförbundets vägnar
>PIC FILE= "L_2002114EN.042703.TIF">
>PIC FILE= "L_2002114EN.042704.TIF">
JOINT DECLARATION BY THE CONTRACTING PARTIES
on the Revision of Article 4
The Contracting Parties undertake to revise Article 4 of the Agreement on mutual recognition in relation to conformity assessment to include in particular products originating in other countries with which the Parties conclude agreements on mutual recognition in relation to conformity assessment, once such agreements have been concluded.
At that point the provisions of Chapter 12 in Section V of this Agreement will be revised.
JOINT DECLARATION
on the Mutual Recognition of Good Clinical Practice and Inspections Relating thereto
For medicinal products, the results of clinical trials carried out on the territory of the Parties to this Agreement are currently accepted for inclusion in applications for marketing authorisations and their variations or extensions. In principle, the Parties agree to continue to accept these clinical trials for the purpose of marketing authorisations applications. They agree to work towards an approximation of Good Clinical Practice, namely by implementing the current Declarations of Helsinki and Tokyo and all guidance relevant to clinical trials adopted in the framework of the International Conference on Harmonisation. However, due to legislative developments concerning inspections and authorisations of clinical trials in the European Community, detailed arrangements for the mutual recognition of the official supervision of these trials will have to be considered in the near future and laid down in a specific Chapter.
JOINT DECLARATION
by the Contracting Parties on Updating the Annexes
The Contracting Parties undertake to update the Annexes to the Agreement on mutual recognition in relation to conformity assessment not later than one month after its entry into force.
JOINT DECLARATION
on Further Negotiations
The European Community and the Swiss Confederation declare their intention of undertaking negotiations to conclude agreements in areas of common interest such as the updating of Protocol 2 to the 1972 Free Trade Agreement and Swiss participation in certain Community training, youth, media, statistical and environmental programmes. Preparatory work for these negotiations should proceed rapidly once the current bilateral negotiations have been concluded.
DECLARATION
on Swiss attendance of committees
The Council agrees that Switzerland's representatives may, in so far as the items concern them, attend meetings of the following committees and expert working parties as observers:
- Committees of research programmes, including the Scientific and Technical Research Committee (CREST)
- Administrative Commission on Social Security for Migrant Workers
- Coordinating Group on the mutual recognition of higher-education diplomas
- Advisory committees on air routes and the application of competition rules in the field of air transport.
Switzerland's representatives shall not be present when these committees vote.
In the case of other committees dealing with areas covered by these agreements in which Switzerland has adopted either the acquis communautaire or equivalent measures, the Commission will consult Swiss experts by the method specified in Article 100 of the EEA Agreement.
Information relating to the entry into force of the seven Agreements with the Swiss Confederation in the sectors free movement of persons, air and land transport, public procurement, scientific and technological cooperation, mutual recognition in relation to conformity assessment, and trade in agricultural products
The final notification of completion of the procedures necessary for the entry into force of the seven Agreements in the sectors free movement of persons, air and land transport, public procurement, scientific and technological cooperation, mutual recognition in relation to conformity assessment, and trade in agricultural products between the European Community and its Member States, on the one hand, and the Swiss Confederation on the other hand, signed in Luxembourg on 21 June 1999, having taken place on 17 April 2002, these agreements will enter into force, simultaneously, on 1 June 2002.
Markierungen
Leseansicht