Vorherige Seite
    Regulation No 6 of the Economic Commission for Europe of the United Nations (... (42014X0718(01))
    56 - 579 - 10
    Nächste Seite
    EU - Rechtsakte: 11 External relations
    Where grouped, combined or reciprocally incorporated lamps have been found to comply with the requirements of several Regulations, a single international approval mark may be applied consisting of a circle surrounding the letter ‘E’ followed by the distinguishing number of the country which has granted the approval, and an approval number. This approval mark may be located anywhere on the grouped, combined or reciprocally incorporated lamps, provided that:
    4.3.2.1.1.
    It is visible after the installation of the lamps;
    4.3.2.1.2.
    No part of the grouped, combined or reciprocally incorporated lamps that transmits light can be removed without at the same time removing the approval mark.
    4.3.2.2.
    An identification symbol for each lamp appropriate to each Regulation under which approval has been granted, together with the corresponding series of amendments incorporating the most recent major technical amendments to the Regulation at the time of issue of the approval and, if necessary, the required arrow shall be marked:
    4.3.2.2.1.
    Either on the appropriate light-emitting surface;
    4.3.2.2.2.
    Or in a group, in such a way that each lamp of the grouped, combined or reciprocally incorporated lamps may be clearly identified.
    4.3.2.3.
    The size of the components of a single approval mark shall not be less than the minimum size required for the smallest of the individual marks by the Regulation under which approval has been granted.
    4.3.2.4.
    An approval number shall be assigned to each type approved. The same Contracting Party may not assign the same number to another type of grouped, combined or reciprocally incorporated lamps covered by this Regulation.
    4.3.2.5.
    Annex 3, Figure 2, to this Regulation gives examples of the arrangement of the approval marks for grouped, combined or reciprocally incorporated lamps with all the abovementioned additional symbols.

    4.3.3.   Lamps reciprocally incorporated with other lamps, of which the lens may also be used for other types of headlamps.

    The provisions laid down in paragraph 4.3.2 above are applicable.
    4.3.3.1.
    In addition, where the same lens is used, the latter may bear the different approval marks relating to the different types of headlamps or units of lamps, provided that the main body of the headlamp, even if it cannot be separated from the lens, also comprises the space described in paragraph 3.3 above and bears the approval marks of the actual functions.
    If different types of headlamps comprise the same main body, the latter may bear the different approval marks.
    4.3.3.2.
    Annex 3, Figure 3, to this Regulation gives examples of approval marks for lamps reciprocally incorporated with a headlamp.
    4.4.   The approval marking shall be clearly legible and indelible. It may be placed on an inner or outer part (transparent or not) of the device which cannot be separated from the transparent part of the device emitting the light. In any case the marking shall be visible when the device is fitted on the vehicle or when a movable part such as the hood or boot lid or a door is opened.

    5.   GENERAL SPECIFICATIONS

    5.1.
    Each device supplied shall conform to the specifications set forth in paragraphs 6 and 8 below.
    5.2.
    The devices must be so designed and constructed that under normal conditions of use and notwithstanding the vibrations to which they may be subjected in such use, their satisfactory operation remains assured and they retain the characteristics prescribed by this Regulation.
    5.3.
    In the case of light source modules, it shall be checked that:
    5.3.1.
    The design of the light source module(s) shall be such as:
    (a) that each light source module can only be fitted in no other position than the designated and correct one and can only be removed with the use of tool(s);
    (b) if there are more than one light source module used in the housing for a device, light source modules having different characteristics can not be interchanged within the same lamp housing.
    5.3.2.
    Markierungen
    Leseansicht
    Verwendung von Cookies.

    Durch die Nutzung dieser Website akzeptieren Sie automatisch, dass wir Cookies verwenden. Cookie-Richtlinie

    Akzeptieren